Hi,
You first have to go to the pain of truly resetting the device. Either attach it to 24 volts so you can click the button, or attach a switch so you can do the toggle exclude/reset. I truly do not understand why you cannot reset/exclude the qubino using the build in switch on 230 volts. It makes it a pain.
Once you relay got it reset, follow the standard instructions to include, but be sure to have it within one meter of the Vera. that is the scenario I managed to get it working. For some reason with 7.30 you have to include any device that supports secure classes within that one meter range. Before only locks required that. So yeah, it is a 7.30 thing as far as i can tell.
Well, if you do not know you should keep your fingers of the shiny bits that it is not for you is it
I don’t have any with a switch attached, so it actually requires much more fiddling and chance of a shock. Others like Fibaro do have reset via a simple button on the device. Much easier.
I had some effect (occasional partial exclude) using the button, but sure did not prepare the device to be able to be included on a different controller.
So… I ordered a fresh qubino. Included next to vera. Instant succes. Default name etc.
But then… I FORGOT TO INCLUDE THE TEMPERATURE SENSOR!
I thought maybe the prrvious device was faulty? So I excluded the device to reinclude with the ensor attached.
Same FR#CKING pain errors again. Why is it so hard to make a good include and exclude process with clear and consistent error messages? I thinkvI have hadaboit 12 or so different error messages and I cannot include it at all anymore…
And vera says: well yeah you have a massive network.
But I dont! I have a massive NUMBER of all thos frikking ghost devices and failed pairings Vera!
Edit: unpairing device is not possible with 230v and switch connect. Only the S button will do. And also with UNpairing I get comm error S-2…
Edit2: reset 24v with S button more than 6 sec
Inclusion on vera gives
Exchanging security key
Failed to Exchange
ERRROR cannot send network key
I resetted via 24v qubino again. Could not delete device in vera untill I rebooted her. Then I ended up with40 devices… and at this point it seems I am just doing something…
Yes ungood . But most frustrating is that vera support is not at all capable of responding correctly (in terms of helping). For about 8 years I always hear the same result… wait for new firmware, sent to development, sent to level 2 or 3, your network is too big, al-ways something else…
And for some reason just trying, waiting, error,it starts workibg after … whatever but most of the times I end up at buting another brand that is supported but then its not.
Sorry for my frustrations
Edit: and from now resetting 24v qubino, rebooting vera adding device I only get "WARNING: Cannot get security scheme.
And now the device lays on top of vera.
Strange thing is the wizard does go further to ask for a name and room (device detected! it says) but it ends up with errors.
I think your frustration is well warranted.
Mine are nothing like as deep set, but again, my outside temperature sensors stopped working yesterday. Just waiting to see if a restore to yesterday’s set up will fix it (so far 3 out of 4 are back up) or if I need to do the exclude / include / rebuild reactors / recreate graphing dance…
WTF update: tried to view logging etc. Did not work etc. I then disabled verbode and lock log (whixh was enabled by vera support) and then suddenly (I did not do anything!) it started pairing etc… now it kinda works… althought I do have a ghost device _GET_LANG(generic_se…)…
I stopped using support, since they usually try what I already tried, but when I have to, I always remind them to not enable verbose logging, because my unit become unstable. What you see is normal: your unit is doing other things and secure keys exchange is failing. Removing the verbose logging gives you more power and the secure key exchange never reaches its timeout.
Another frustrated user with exactly the same issues…
Failed to set up security error
Error occurred with Qubino dimmer and Fibaro wall plug.
Tried adding devices real close to the vera box (this i a pail because the dimmers are built in the wall)
in the mean time: ALL of my zwave devices have dissapeared from my dashboard.
But I think that is not really related but a database corruption. Retoring a previous backup did not solve this unfortunately.
Contacted support, but going totally mad!
Firmware: 1.7.5186 (7.31)
*** EDIT. ***
My devices have re-appeared … When I was resoring the backup I forgot to tick the box “restore ZWAVE network”
Pfff … Now on with adding those devices
Best Home Automation shopping experience. Shop at Ezlo!